Insulation Materials Published Sources

The insulation material described in this article is electrical insulation material.According to the national standard GB/T 2900.5-2002, the definition of insulating materials is "material used to insulate the device".It's the material that stops the current from passing.

Its resistivity is very high, generally in 10 ^ 9 ~ 10 ^ 22 Ω m. range.In the motor, the insulation material around the conductor isolates between turns and isolates from the grounded stator core to ensure the safety of the motor.

Main products

Products: nylon PA6, PA66 nylon MC nylon POM POM PP polypropylene PTFE teflon PEEK polyether ether ketone plate bar PSU polysulfone rods PEI ultem plate bar PES sulfone julong plate bar PVDF polyvinylidene fluoride PET together PETP terephthalic acid ethyl ester 2 PPO polyphenylene oxide plate bar PPS PPS plate bar CPVC chlorinated polyvinyl chloride (PVC) PMMA acrylic rods ABS acrylonitrile PBT, poly (butyl glycol terephthalate PC polycarbonate PE poly (PVC PVC PVC UPE ultra-high molecular polyethylene PAI polyamide imide PI polyimide PU polyurethane PPA to benzene 2 acyl phenylenediamine PFCC PBI company polybenzimidazole PLA phenolic resin cotton polyester bakelite phenolic composite slab carbon fiber plate cold punching board (above is plastic products of insulation materials industry norms.)Insulation materials should have the following material: insulation adhesive laminated substrate to enhance products, such as phenolic resin paper-based enhance PFCP, phenolic resin duct enhance PFCC, glass fiber reinforced epoxy resin 3240 fr4, glass fiber reinforced polyester resin SMC, DMC, etc

characteristic

Chemical erosion resistance, gloss, part of transparent or translucent, mostly good insulation, light weight and strong, easy processing can be mass production, the price is cheap, wide range of USES, utility, easy coloring, part of high temperature resistant, storage of goods can have the effect of moisture-proof plastic also divided into domestic plastics and engineering plastics, mainly USES the generalized defined, such as PE, PP cheap, available in a variety of different types of machines for production.Engineering plastic is more expensive, but the material stability and physical properties are much better. In general, it has both rigidity and toughness.

PVC transparent plastic sheet: introduce advanced technology from abroad, and choose a high strength, high transparent plastic plate produced by advanced imported raw materials.

Most plastic light, chemical stability, not rust;

Good impact resistance;

Good transparency and abrasion resistance;

Good insulation and low thermal conductivity;

It is generally good in shaping, coloring and low processing cost.

Most plastics have poor heat resistance, high thermal expansion rate and easy combustion.

Poor size stability, easy deformation;

Most plastics have low temperature and low temperature.

It is easy to age;

Some plastics are soluble in solvents.

Plastic can be divided into two types: thermosetting and thermal plasticity. The former cannot be reshaped and used, and the latter can be repeatedly produced.There are two basic types of plastic polymer structure: the first is the linear structure, and the polymer compounds with this structure are called linear polymer compounds.The second is body structure, which is known as a type of polymer.Some of the polymers have branched chains, known as branched polymer, which belong to the linear structure.Some polymers, although they have crosslinks between molecules, are less crosslinked, called reticular structures, and belong to body structure.Two different structures show two opposite properties.

The linear structure (including branched chain structure) is characterized by its elasticity, plasticity, and the ability to dissolve in solvents, and its hardness and brittleness are small.Because there are no independent large molecules, there is no elasticity and plasticity, so it can't dissolve and melt. It can only be swelling, hardness and brittleness.Plastic is a polymer of two kinds of structure, made of linear polymer is thermoplastic plastic, which is made of polymer and thermoset plastic.

Published sources

By high performance liquid chromatography (HPLC) determination of antioxidant content in plant insulating oil, mix sample under test and methanol oscillation, after two centrifugal extraction, merge the capacity; the supernatant fluid with methanolExtract after 0.45 mu m filter membrane filtration into chromatographic column analysis, ultrapure water - methanol as mobile phase, using uv detector, according to retention time for qualitative analysis, according to the peak area for quantitative detection.Under the condition of determination, concentration range of 0.1 ~ 0.5 mg/mL of 3 kinds of antioxidants (PG, BHA, butylated hydroxytoluene) has a good linear relationship, the correlation coefficient R2 more than 0.999, the detection limit is 0.003 ~ 0.01 mg/mL, quantitative limit of 0.01 ~ 0.033 mg/mL;The recovery rate of the blank sample is 98% ~ 108% and the relative standard deviation is less than 4%.This method is used in the test of the antioxidant in the oil FR3 of cooper oil and the test of the test of additive standard. The results are accurate and the recovery rate is high.